02 - SF2P SUZUKI Oxygen Sensor Eliminator Set

02 - SF2P SUZUKI Oxygen Sensor Eliminator Set

02 - SF4PGB SUZUKI Oxygen Sensor Eliminator Set

02 - SF4PGB SUZUKI Oxygen Sensor Eliminator Set

02 - SF4PGB SUZUKI Oxygen Sensor Eliminator

  Improved throttle response, smoother power delivery.
  Supports FI mods such as Power Commander.
  Cheaper than replacing a faulty o2 sensor.
  Simple to fit, No cutting or soldering required.

125 RV 125 Van Van 2007-2018, 400 BURGMAN 400 2018-2020, 650 DL 650 V-STROM 2012-2020, 650 SV 650 /S 2007-2014, 650 SV 650 /S 2017-2020, 750 GSX-S 750 2018-2020, 800 C 800 intruder 2005-2008, 1000 GSXR 1000 L7-M0 2017-2020, 1000 GSX-S 1000 2018-2020, 1000 KATANA 1000 2019-2020, 1250 GSX 1250 FA 2010-2017, 1500 C 1500 INTRUDER 2005-2008

£12.99
Availability: In stock
SKU
02 - SF4PGB

The O2 sensor which is installed in the stock exhaust systems of motorcycles are used by the Manufacturer to adjust the fuelling in order to pass the emission tests for street homologation.

This is done only in a very limited RPM range under certain load situations.

The intention behind it is not to improve the performance of the machine.

It's aimed to reduce the emissions of the engine in the specific RPM/Load situations which are tested during the homologation process.

This can result in delayed throttle response or unsteady power delivery. If you replace your silencer or exhaust system or fuelling, it's suggested to remove the installed sensor and replace it with this eliminator.

The eliminator simulates the signal given from the O2 sensor under optimal A/F ratio conditions. This allows the bike to run under best performance conditions. If you install an aftermarket exhaust, remove the catalyst, install a power commander or perform similar modifications we strongly suggest installation of an O2 sensor eliminator for the best performance of your machine.

 

This Eliminator fits the following models

125

RV 125 Van Van 2007-2018

2007-2018

02 - SF4PGB

1

M12 x 1.25mm

400

BURGMAN 400

2018-2020

02 - SF4PGB

1

M12 x 1.25mm

650

DL 650 V-STROM

2012-2020

02 - SF4PGB

1

M12 x 1.25mm

650

SV 650 /S 

2007-2014

02 - SF4PGB

1

M12 x 1.25mm

650

SV 650 /S 

2017-2020

02 - SF4PGB

1

M12 x 1.25mm

750

GSX-S 750

2018-2020

02 - SF4PGB

1

M12 x 1.25mm

800

C 800 intruder

2005-2008

02 - SF4PGB

1

M12 x 1.25mm

1000

GSXR 1000 L7-M0

2017-2020

02 - SF4PGB

1

M12 x 1.25mm

1000

GSX-S 1000      

2018-2020

02 - SF4PGB

1

M12 x 1.25mm

1000

KATANA 1000

2019-2020

02 - SF4PGB

1

M12 x 1.25mm

1250

GSX 1250 FA 

2010-2017

02 - SF4PGB

1

M12 x 1.25mm

1500

C 1500 INTRUDER

2005-2008

02 - SF4PGB

1

M12 x 1.25mm

We always recommend removing your o2 sensor and fitting a blanking plug as a non heated o2 sensor can become damaged.